Broan 114 Guide d'installation télécharger pdf

MODEL 114

Page 1

WARNING

WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,

OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. All electrical work must be done in accordance with local and/or

National Electrical Code as applicable. For safety, this product

must be grounded. If you are unfamiliar with methods of installing

electrical wiring, secure the services of a qualified electrician.

2. Turn off power at service entrance before installing wiring, ser‑

vicing, or cleaning this product.

3. Do not install heater upside down or sideways. Heater must be

located in the horizontal position.

4. Do not recess louvered face of the heater more than three inches

from the vertical face of any overhang (cabinet).

5. Do not locate heater behind doors, furniture, etc., where the air

flow to the unit will be restricted.

6. To avoid electrical shock; do not install heater within arm’s length

of tub or shower enclosure.

7. To avoid motor bearing damage and noisy and/or unbalanced

impellers, keep drywall spray, construction dust, etc., off power

unit.

8. Provide this heater with a separate electrical circuit following

directions under “Wire the Heater” section.

9. This product is equipped with a thermostat which may start it

automatically. Turn off power at service entrance before cleaning

or servicing.

10. This heater includes a visual alarm to warn that parts are getting

excessively hot. If the alarm lights are activated, immediately

turn the heater off and inspect for any objects on or adjacent to

the heater that may cause high temperatures.

11. Please read specification label on product for further information

and requirements.

KICKSPACE

HEATER

Factory Wired 240/208 V.A.C.

READ AND SAVE THESE INSTRUCTIONS

VOLTS WATTS AMPS BTU/HR

240 1500 6.3 5120

208 1125 5.4 3840

120* 1500 12.5 5120

120* 750 6.3 2560

PLAN THE INSTALLATION

This heater is designed for installation in an enclosed space such

as under a counter or kickspace to provide warm, gentle heat at

the floor level. Reread Safety Notes 3 through 8 for guidelines in

planning the installation.

The Model 114 is factory wired for 240/208 V.A.C. operation. It offers

a choice of heat outputs and can be internally connected for multiple

wattages at different voltages shown in the table below.

All ratings are 1‑Phase, 60 Hertz.

*See “FIELD CONVERSION TO 120 V.A.C.” section.

INSTALL THE HEATER

1. Mark the intended mounting location in the base plate under the

counter or kickspace, and remove required material to provide

for easy insertion and removal of the heater cabinet.

2. The unit will be secured in place with screws through the side

angle support brackets. Provide adequate material behind side

angle support for secure mounting.

SIDE

ANGLE SUPPORT

BRACKETS

Installer: Leave this manual with the homeowner.

Homeowner: Use and Care information on page 3.

1 2 3 4 5 6 7 8

Résumé du contenu

Page 1 - KICKSPACE

MODEL 114 Page 1WARNINGWARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:1. All electrical work mus

Page 2 - THERMOSTAT INSTALLATION

MODEL 114 Page 2THERMOSTAT INSTALLATIONFIELD CONVERSION TO 120 V.A.C.If a 120 V.A.C. circuit is to be used, make wiring changes as follows:1. Disco

Page 3 - MAINTENANCE

MODEL 114 Page 3WIRE THE UNITWARNING: Disconnect power at service entrance before wiring this product.1. Run electrical power cable to installation

Page 4 - WARRANTY

MODEL 114 Page 4 KEY PART NO. NUMBER PART DESCRIPTION 1 99522899 Cover (White) 2 99522400 Cycling Thermal Overload Limit Switch 3 99521

Page 5 - ESPACIOS BAJO GABINETES

MODEL 114 Page 5ADVERTENCIAADVERTENCIA: PARA REDUCIR EL RIESGO DE INCENDIOS, DESCARGAS ELÉCTRICAS O LESIONES P ERS O N A LES O BSE RV E L A

Page 6 - EL SITIO DE LA INSTALACIÓN

MODEL 114 Page 6Si se va a utilizar un circuito de 120 VCA, efectúe los siguientes cambios de conexión:1. Desconecte el cable blanco de la termi

Page 7 - MANTENIMIENTO

MODEL 114 Page 7CABLEADO DEL CALEFACTORADVERTENCIA: Desconecte el suministro eléctrico en la entrada de servicio antes de realizar el cableado de es

Page 8 - GARANTIA

MODEL 114 Page 8 CLAVE NÚMERO No. DE PIEZA DESCRIPCIÓN DE LA PIEZA 1 99522899 Cubierta (blanca) 2 99522400 Interruptor limitador de sobrec

Commentaires sur ces manuels

Pas de commentaire

Broan 114 Guide d'installation

Naviguer en ligne ou télécharger Guide d'installation pour Chauffages d'appoint Broan 114. Broan 114 Installation Guide Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Chauffages d'appoint Broan 114